Guide

Bargeboards on Stroud gables: repair and replacement

The board that follows the slope of a gable end takes weather from three sides and gets looked at least. Whether a failing board needs a repair or a replacement often depends as much on the verge above it as on the timber.

Walk down any terrace in Stroud and the gable ends tell you a lot. Where a roof stops at the side wall of a house, the sloping timber or plastic board under the edge of the roof is the bargeboard. Some people call it a verge board or a gable board. The edge of the roof that sits above it, where the tiles or slates finish at the gable, is the verge. The board closes the gap between the two and hides the ends of the roof timbers.

Eaves boards get most of the attention because the gutter hangs off them. Bargeboards have no gutter, so water that gets behind them has nowhere obvious to go, and a failing one can go unnoticed from the ground for years. This guide covers how the boards rot, repair against replacement, timber against uPVC, and what we check on the verge when a board comes off. For the eaves side, see our guide to rotten fascia boards. The wider picture is on our gutters, soffits and fascias page.

A bargeboard is not a fascia, and the difference matters

Both boards sit at the edge of the roof, which is why they get confused. A fascia runs along the eaves, the low edge of the roof, and carries the gutter. A bargeboard runs up the rake, the sloping edge of a gable, and carries nothing except itself and a coat of paint. Because the two meet at the corner, they are often replaced together, but they fail for different reasons and are fitted differently.

On a traditional gable the board is nailed to the ends of a projecting timber frame, sometimes called a ladder or lookout frame, which carries the overhang of the roof out past the wall. Beneath the board there may be a small soffit, a flat panel boxing in the underside of the overhang. On a plainer modern house the board may simply be fixed to the end of the roof timbers with no overhang to speak of.

Plain, cut and decorative boards

Gable boards come in more shapes than eaves boards. A plain bargeboard is a straight length of timber or uPVC. Older houses, especially Victorian villas and the larger terraced houses on the hillsides above Stroud, can carry cut or shaped boards with scalloped or pierced edges, finials at the apex and a pendant hanging from the point. Those are a different job. They have to be copied from the original, and the pattern matters as much as the material, which is where our guide to rooflines in conservation areas becomes relevant.

Where gable boards rot, and why

Timber fails where water can get in and cannot get out again. A bargeboard has several places that fit that description.

The end grain at the bottom tip

The lowest end of the board, where it meets the eaves, is cut across the grain, and end grain drinks water. It also sits right where the gutter or eaves corner shed their water, so the foot of the board is often the first part to go soft. Paint that has cracked at the cut end lets the moisture straight in.

The top edge under the verge

The upper edge of the board sits under the verge, where tiles or slates overhang. If the verge has worn, if the pointing has cracked or if a tile has slipped, rain can run down onto the top of the board and sit there. This is why we look at the verge before we judge the board. Rot that starts at the top edge is often a roof problem wearing a roofline disguise.

The apex joint

Where the two boards meet at the peak of the gable there is a joint that opens as the timber moves with the seasons. It is exposed from above and from both sides. Open joints take in water, and that rots the timber behind the joint first, so the damage is easy to miss.

Fixings and the frame behind

Boards are held on with nails or screws into the timber behind. When those corrode or the frame behind rots, the board starts to pull away and bow. A bargeboard that moves in the wind may have sound timber and a failing frame, or the reverse. We test both before we say which job it is.

Repair or replace: how the decision is made

With timber, a repair is a real option as long as the damage is limited and the wood around it is sound. The test is the same one a joiner would use: probe the board with a bradawl or a screwdriver tip. Sound timber resists. Rotten timber crumbles, and the tool sinks in.

What we findUsual answer
Soft spot at the foot of the board, rest soundCut out the bad section and splice in new timber, then prime and paint
Open apex joint, timber soundRe-make the joint, seal the end grain, repaint
Rot along the top edge from a verge leakFix the verge first, then repair or replace the board
Rot through most of the board, or the frame behind is softReplace the board and renew the timber behind it
Cut, carved or decorative board with local rotRepair in timber and copy any missing section from the original

Why a patch can be the wrong call

Filler and paint over rot do not stop it. Where the damage has gone into the timber behind, a cosmetic fix looks fine for a season and then fails again, and a second visit with a scaffold costs more than doing the job properly the first time. Our survey photographs show you exactly where sound wood ends and soft wood begins.

On the other hand, replacing a whole run of good boards just because one section has failed is wasteful, and on an older house it can strip away original detail. We would rather splice than strip where the board allows it.

Timber or uPVC for a replacement gable board

Both are used, and each has a case. The decision usually comes down to the age and character of the house and how much upkeep you want to carry.

Timber

Painted softwood is the traditional choice and still the right one on many older houses. It can be shaped to match an existing board, a failed section can be spliced out, and it looks like what was there before. The cost is maintenance. Timber needs priming on every cut face, including the ends, and repainting at intervals so that the paint film never fails.

uPVC

A uPVC board is a hollow plastic section that needs no painting. MyBuilder's 2026 guide gives uPVC fascias and soffits a typical replacement interval of 10 to 20 years, with a check every five; gable boards are the same plastic section, so that is the nearest published guide. A retailer, Plastic Centre, puts good-quality uPVC at 20 to 40 years in a 2026 article, so published figures disagree and the real life depends on the product and the exposure. A plastic board is a poor fit where the original was shaped or carved, and a replacement is a visible change in the look of a gable.

What the work costs

MyBuilder's 2026 price guide lists a bargeboard at about £195, fascia at £80 to £150 per metre and soffit at £100 to £180 per metre, with scaffold at £20 to £40 per m². Treat these as national ranges, never as our quote. Our written quote follows the survey, covering gable boards, any soffit and scaffold. Our roofline costs guide goes through what moves those numbers.

The verge above the board

A bargeboard job puts the verge in plain view, because the board has to come away from the edge of the roof to be replaced. The moment the board is off is the time to inspect the edge, and the main reason a gable should not be treated as a boards-only problem.

Mortar or mechanical fixing

On many older roofs the verge tiles or slates are bedded in mortar, and the mortar has been cracking and falling away for years. BS 5534:2014 says mortar alone should not be relied on to hold the verge down; the verge units should be mechanically fixed as well. A dry verge system, tested to BS 8612, does without mortar and holds the verge with clips or fixings, and it covers the top edge of the board neatly. If the verge on your gable is mortar that has failed, replacing the board without dealing with the verge shortens the new board's life.

The overhang and the water line

The tiles or slates at the verge should overhang the board so that rainwater drips clear of it rather than tracking back underneath. On a roof where the verge has been cut back or never overhung enough, the board takes the run-off. We check how far the edge projects, whether the board sits tight under the verge, and whether the underlay or any tile fillet is doing its job. If a board is fitted tight and sealed against the underside of the verge, it can hide a leak for years.

Underlay and the rafter ends

On a gable the underlay (the waterproof membrane beneath the covering) needs to be lapped properly at the edge. Rotten rafter ends or ladder timbers behind the board are more serious than the board itself, because they carry the roof edge. We would rather find that during the repair than after it, and we will tell you before we go further if it changes the job.

Soffits, ventilation and the corner at the eaves

Where a gable has an overhang, the small soffit under the board can be forgotten. It protects the timber ends from the weather and keeps birds and insects out. If it is rotten, repair it with the board, because the two share the same fixings and the same water problems.

The corner where the bargeboard meets the eaves fascia deserves attention too. A neat mitre or butt joint keeps water out, and a poor one lets it in. When we replace gable boards we match the joint to the eaves boards, whether those are timber or plastic. If the eaves are being renewed in the same visit, doing both at once saves scaffold time and gives a cleaner finish.

Eaves boards and soffits often carry vents that help the roof void breathe, and a new plastic soffit can be fitted with them in place. Vent strips are a topic of their own: see soffit vents and roofline ventilation.

Working at height on a gable

Gable ends are tall, and working on them from a ladder is not good enough for a job with this much cutting and fixing. Scaffold is normal, and on steep terraced lanes it has to be planned around narrow access and shared drives. That planning goes into the quote before work starts.

If you can see daylight, a gap or dark staining along a bargeboard from the ground, take a photograph and send it over. It is often enough to tell us whether the job is a splice or a replacement before we visit.

What happens on the day, and what stays with you

A gable boards job starts with the survey. We look at the boards, the verge, the frame behind and the soffit, and photograph your own roof so the quote reflects what is actually there. The written quote then covers scaffold, removal, new boards, any frame repairs, paint or finish, and waste, and you decide what to approve.

On the day, the old boards come off, the timber behind is checked and repaired, and the new boards go on with sealed joints. Timber is primed on every face before it goes up. Any verge repair is done in the same visit if it is part of the agreed job. Site cleared, waste taken away, and we put our 10-year workmanship guarantee in writing.

Bargeboard work on a listed house, or in one of Stroud District's conservation areas, can need consent before it begins. We explain what applies and who to ask; the council confirms it.

Gable boards: questions before you replace them

Can one rotten section of a bargeboard be spliced rather than replacing the whole board?

Yes, in timber, when the rot is limited to the foot of the board or one joint and the wood around it is sound. The bad section is cut out and a new piece is joined in, primed and painted. If probing shows soft wood running further or the frame behind is affected, a full replacement is the sounder call.

Do bargeboards and fascias have to be replaced at the same time?

No, but it often makes sense. They meet at the corner, they share the scaffold, and a matched finish looks better than a new gable board against a tired eaves board. If the fascia is sound, we can replace only the bargeboards and match the joint.

Why does the verge need checking when a bargeboard is replaced?

Because rot along the top of a gable board often comes from the verge above it. If the mortar has failed or the overhang is too short, water runs onto the new board as it did the old one. Dealing with both in one visit costs less than coming back.

Get your roof priced

Tell us what's happening and we'll call you back with a time to look at it.

  • Guide prices before we visit
  • A written quote
  • 10-year workmanship guarantee

Rather talk? 01453 933613

Call Get a quote